Hardware User’s Manual Megapixel Day & Night Bullet Network Camera Quality Service Group OB-500Af Series
7 Chapter 3 - Device Appearance Description < Front Panel > < Rear Panel > Lens Light Sensor IR LED
8 Please open the top case with the screwdriver. < Top > Micro SD card slot and HW Reset Button
9 < Extension I/O Terminal Block > The Network Camera provides an extension I/O terminal block which is used to connect the camera with extern
10 < Hardware Reset > The Reset Button can be used to reboot the camera or restore it to factory default settings. If the came
11 Chapter 4 - Installation 4.1 Hardware Installation WARNING - Do not mount the camera on a soft material. The camera may fall and be damaged. A
12 B. Bracket Installation Use the screws to lock the bracket along with the Bullet housing. C. Wall Installation a. Drill three holes into
13 a. PoE Connection For the Power over Ethernet connection, construct the PoE cable using the pin definitions of the RJ45 connector below and refe
14 b. If using a non-PoE switch: i. Use a standard RJ-45 cable to connect the camera to a PoE Injector. ii. Use a standard RJ-45 cable to connec
15 4.3 System Requirements Operating System: Microsoft Windows XP Home Edition SP2 Microsoft Windows XP Professional SP2 Computer: IBM PC/AT
16 4.4 Software Installation In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refe
Review History: 1. Separate User Manual into HW and SW. 2. Merge OB-500Af/OB-400Af/OB-300Af/OB-200Af/OB-130Af into this User Manual 3. Change pict
17 B. In the Install Shield Wizard dialog box, click <Next> to continue. C. Read the End-User License Agreement and check the option “I acc
18 D. Select either “Complete” setup or “Custom” setup to install the system. a. If COMPLETE SETUP is selected: i. All program features will
19 iii. Select to create shortcuts. Click <Next> to continue. iv. The installation information will be displayed. Click <Next>
20 v. To launch EasyConfig or PC-NVR Standard, select the application and click <Finish>. When launching the PC-NVR program, please refer to
21 iii. Select the features to install. Click <Next> to continue. iv. Click <Change> to change the appointed folder where installatio
22 v. Select programs to create shortcuts. Click <Next> to continue. vi. The installation information will be displayed. Click <N
23 E. To launch EasyConfig or PC-NVR Standard, select the application and click <Finish>. When launching the PC-NVR program, please re
24 4.4.1 EasyConfig To launch EasyConfig, select EasyConfig from the start menu. If Complete Setup type was used in the software installat
25
26 B. Select either “Simple Mode” or “Professional Mode” to obtain the camera’s IP settings. If “Simple Mode” is selected, EasyConfig will
Table of ContentsBefore You Use This Product ... 1 Regulatory Inf
27 C. There may be many cameras in the local network. Differentiate the cameras using their UPnP name. Double click on the camera from the survey l
28 If <Set IP Address configuration manually> is selected, the following pages will be displayed.
29 E. If the camera supports the EasyLinkTM function, the following page will be displayed. Otherwise, this page will not be shown. *If desire
30 F. When the IP address settings have been configured, the screen will either display a successful or failed connection message. If the connectio
31 c. If the connection was successful, the user will see the message: “Congratulations. The installation of the camera is complete.”
1 Before You Use This Product In many countries, there are laws prohibiting or restricting the use of surveillance devices. This Network
must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement:
3 pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Conformement a la reglementation d'Industrie Canada, le present em
4 Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co
5 Chapter 1 - Package Contents Please check to make sure the product package contains all the accessories listed below. A. Camera Pack
6 Chapter 2 - Bullet Network Camera Overview The Brickcom Bullet SERIES is a Bullet network camera. It adopts a megapixel sensor whic
Commentaires sur ces manuels