United Digital Technologies KCM-7911 Manuel

KCM-7911 H.264 4-Megapixel IP D/N PoE Outdoor Hemispheric Camera with Advanced WDR (DC 12V / PoE) Ver. 2013/10/

www.acti.com Hardware Manual 10 Installation Procedures There are several mounting options that you can use to install the camera.

www.acti.com Hardware Manual 11 Vertical Pole Mount Suitable when mounting the camera on a vertical pole. PMAX-0310

www.acti.com Hardware Manual 12 Installing the Camera on a Flat Surface This section covers the step-by-step procedures in directly

www.acti.com Hardware Manual 13 Step 2: Open the Camera Cover 1. Loosen the three (3) screws using the supplied hex wrench. 2. L

www.acti.com Hardware Manual 14 Step 3: Prepare for Waterproof Installation The camera comes with two (2) glands used for waterproo

www.acti.com Hardware Manual 15 Step 6: Close the Cover Tighten the three (3) screws to secure the cover. Step 7: Access the Ca

www.acti.com Hardware Manual 16 Waterproof Solutions There are two ways to do the waterproof cabling installation:  Waterproof

www.acti.com Hardware Manual 17 3. Insert the sealing insert with claw. 4. Attach the cable gland body to the hole of the ca

www.acti.com Hardware Manual 18 6. Insert the claw and rubber insert into the cable gland body and then attach the clamping nut to

www.acti.com Hardware Manual 19 Waterproof Solution with Conduit This section describes the procedures to waterproof the cabling co

www.acti.com Hardware Manual 2 Table of Contents Precautions 4 Safety Instructions ...

www.acti.com Hardware Manual 20 4. Insert the sealing rubber and attach it at the end of the flex conduit. 5. Attach the con

www.acti.com Hardware Manual 21 7. Insert the Ethernet cable and other cables (if any) through the conduit gland body.

www.acti.com Hardware Manual 22 Other Connections This section describes the procedures in preparing the external devices that you

www.acti.com Hardware Manual 23 3. Connect the wire with the white stripe to the 12V pin and the other to the GND pin. 4. Ti

www.acti.com Hardware Manual 24 Connecting DI/DO Devices (Optional) Depending on your surveillance needs, you may connect digital i

www.acti.com Hardware Manual 25 To connect output devices (DO), map the pins to one of the pin combinations below: Device Pin Map

www.acti.com Hardware Manual 26 Consequently, to connect a second DI or DO device, wire the connection to Pins 5 to 8. High Voltag

www.acti.com Hardware Manual 27 NOTE: For more information on DI/DO connections, please refer to the Knowledge Base article All abo

www.acti.com Hardware Manual 28 Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera

www.acti.com Hardware Manual 29 When the left mouse is clicked on the camera model name, the default browser of the PC is automatic

www.acti.com Hardware Manual 3 Accessing the Camera 28 Configure the IP Addresses ...

www.acti.com Hardware Manual 30 Use the default IP address of the camera If there is no DHCP server in the given network, the user

www.acti.com Hardware Manual 31 Manually adjust the IP addresses of multiple cameras If there are more than one camera to be used i

www.acti.com Hardware Manual 32 Access the Camera Now that the camera and the PC both have their unique IP addresses and are under

www.acti.com Hardware Manual 33 Upon successful connection to the camera, the user interface called Web Configurator would appear t

www.acti.com Hardware Manual 4 Precautions Read these instructions You should read all the safety and operating instructions before

www.acti.com Hardware Manual 5 Safety Instructions Don’t use the power supply with other voltages This device is likely to be damag

www.acti.com Hardware Manual 6 Safety Check Upon completion of any service or repairs to this video product, ask the service techni

www.acti.com Hardware Manual 7 Introduction Package Contents Camera Cable Gland Conduit Gland Hex Wrench Screw Plugs Screws for

www.acti.com Hardware Manual 8 Physical Description DC 12v Power Input Audio Input / Output Ethernet Port Digital Input

www.acti.com Hardware Manual 9 3) Reset Button The Reset button is used to restore the factory default settings of the camera, inc